The Austin
Taylor 1200 pair cabinets are heavy duty cross connection cabinets manufactured
in marine quality aluminium. They are built to exacting standards for
use in high security or harsh environmental applications.
The
cabinets are supplied as standard with heavy duty stainless steel latches
and there is provision for secondary security locks.
Roof
Double skin pitched roof bolted to body. Alternate roof styles can be
provided on request including flat, high pitched or steep slope versions
to dissuade climbing or sitting on cabinet. The bolted construction
enables the roof style to be changed retrospectively where conditions
dictate.
Body
Fully welded one piece construction in 3mm thick material. In the event
of severe accident damage, the body can be changed without disconnecting
the cross-connection equipment.
Base
3mm hot-dip galvanised steel base. Separated from body by full flange
rubber gasket to prevent galvanic corrosion.
Doors
Single door with heavy duty hinges. Opening to 180 degrees, door can
be lifted off for additional access. Door stay retains the door at 90
and 135 degrees. Replaceable synthetic rubber car boot type seals are
used throughout.
Latches
& Security
Stainless steel latches with nylon pawls operated by heavy duty tee-bar
keys in a variety of vandal resistant standard shapes. Additional customised
styles are available. O type ring seals withing the latch body ensure
lifetime lubrication and IP65 performance. Latches are tested to withstand
a test requirement of 50NM. Provision is made for secondary security
locks to be fitted on assembly or retrospectively by the end user with
removable blanking covers fitted to standard profile cutouts. Fitment
by end user ensures controlled access. Security dogs on the hinge side
of the door prevent the door being removed even if the hinges are forced.
Finally a hasp is provided for an external padlock securing door to
base if required. The side ventilation units are protected against ingress
of inflammable or corrosive liquids by inner boxes.
Equipment
Mounting (Backboards)
Cabinets are supplied as standard with fixings to allow installation
of Krone, MS2 or Strips Cross Connection. Alternatively the cabinets
can be supplied with stainless steel, aluminum, marine ply or chipboard
backboards. Star punched or custom punched units are available in all
three of the metal versions. Optional gauge plates can be provided for
mounting pressure gauges and transducers.
Ventilation
Cabinets can operate in sealed or ventilated mode. In ventilated mode,
convection currents draw fresh air in through louvres at sides of cabinet
forcing warm air out through concealed vents above the doors. Side vents
are protected by insect-proof mesh. Changing between sealed and ventilated
modes can be done easily without additional components. The cabinet
roof has a double skin and air gap to help protect against solar gain.
This "double glazing" also helps to reduce condensation.
Finish
Pre-treatment by chemical etching followed by powder coating with polyester
material in customers choice of colour (standard is green). Multi colour
finishes and silk screened or embossed logos are available on request.
The gloss finish enables graffitti to be removed using mild solvents
or mild abrasive compounds. Damage can be touched up using brush or
aerosol techniques. Repainting is best achieved using two pack polyurethane
compounds although gloss paint can be used.
Dimensions
| Height
(standard roof) |
1220mm |
| Height
(high pitch roof) |
1289mm |
| Width |
728mm |
| Depth |
316mm |
| Door
opening (width) |
640mm |
| Door
opening (height) |
840mm |
| Weight |
55kg |
| Flange
width |
728mm |
| Flange
depth |
340mm |
| Fixing
bolt centres (left to right) |
635mm |
| Fixing
bolt centres (front to back) |
254mm |
| Max
duct capacity |
3 |
Ordering
Information
| Description |
Part
No |
Pallet
multiple |
| 1200
pair cabinet, green |
9CAB216455 |
4 |
| 1200
pair cabinet, black |
9CAB2164A5 |
4 |
|
